ATTEN MS-900 SET 4 U 1

955,90  | MP: 1.147,08 

Доступно као наруџбина на захтев

Шифра производа: AT-ACC031926 Категорија:
  • MCU kontrola visoke tačnosti koristi se za sinhronizovano otkrivanje da li se 3 kanala alata mogu koristiti samostalno i sinhronizovano bez dvojnih smetnji
  • Ugrađeni vakum generator
  • Cela mašina može da obezbedi maksimalnu snagu od 900W
  • Samostalna mašina može istovremeno da izvršava više zadataka rezlemljivanja
  • Veliki ekran koji može grafički prikazati sve vrste parametarskih podataka i poruka
  • Automatsko prepoznavanje svih vrsta alata  i učitavanje odgovarajućih parametara
  • Softver može automatski podesiti preciznu temperaturu 
  • Dostupne su funkcije kao što su stanje pripravnosti, alarm, zaključavanje temperature i resetovanje fabričkih podataka
  • Može pristupiti računaru i izvršiti različita podešavanja

Standardna oprema:

  • Vrh uz ručku:  T130-1.0I
  • Vrh uz pincetu: T100-0.5I
  • Mlaznice: T151-0.8, T151-1.0, T151-1.3 i T151-1.6

Features:

♦  Hot air gun, soldering iron, desoldering gun, electric tweezers and suction pen in one station.

♦  Support 3 channels working. Tools will be identified automatically and loading of corresponding parameters. 

Short press key 1/2/3 to select channel 1/2/3; long press to turn it on/off.

Adjust the temperature value by pressing “▲” or “▼”, long press can be quickly adjusted.

♦  Beep Alarm Function

When the station is power off, long press “▲” and “▼” key and turn on the power switch to turn on/off tone.

 ♦  ℃/℉ available

When the station is power off, long press  and turn on the power switch to change ℃/℉.

♦  Temperature calibration

Short press key 1/2/3 to select channel 1/2/3, press  and key 1/2/3 for more than 3 seconds to enter into temperature calibration mode. Press “▲”or“▼” key to input temperature calibration value ±50℃/90℉.

♦  Auto-sleep function, sleep time setting.

After temperature calibration setting, it will directly enter into sleep time setting. Press “▲”or“▼” key to input sleep time 1-120mins. (default 0min, no sleep.)

♦  PC Software Control System

The PC software can be used under the following operating system: win XP, win 7, win 10.

♦  Software interface included 4 functions modules

1.Communication module

This module displays the communication port, automatic connection of the automatic query port, communication key, expanding and hiding the real-time curve module.

2.Channel parameter setting and status display module. 

This module displays the real-time parameter information and parameter setting of each channel.

3.Serial port command input / info tip module.

This module can manually input the serial port command (see the last page of the instruction manual for serial port command) and prompt for relevant information, including error, important operation, etc.

4.Real-time temperature curve display module.

This module can choose any real-time temperature curve of each channel. 

♦  Setting parameters of each channel by PC

Choose “Open” option to open the channel. Choose “LockParar” the channel temperature will be locked.

“SetTempe”, the temperature value of the channel handle can be set from 150℃-480℃.

“SetAir”, can set the air volume of the air gun (if it is the soldering iron channel, there is no air volume setting option here).

“RunStatus”, is the real-time status of the device working (Normal will be displayed when working normally; “S-e” will be shown when no soldering iron is connected; “SLP” is displayed when dormant and “OFF” is displayed when the channel is closed.

“Type” means type of handle to which the channel is connected.

“Tempe” means the actual temperature value of the handle.

“Air” means the air volume value. (If it is soldering iron channel, there is no air volume setting option here).

Click “SetPararm…” will Pop-up sleep time setting and temperature compensation setting, these parameter are 3 digits number. When setting sleep time or temperature to “10”, please enter “010”. 

♦  Real-time curve display

Click “Path” to set the real-time temperature curve saving address. Choose “Save”, the real-time temperature curve will be saved to the setting address in the form of excel document.

♦  Easy to change replacements https://www.atten.com/product/ms_9004_in1_rework_station_1

Vrhovi – Serija T50

Serija T100

Serija T130

Serija T150

Ručke:

Postolja: S-01 / S-04